We are building a garage from foam blocks

Foam block is a relatively new building material on the market. At the same time, the practice of use has shown that it is very durable, has fairly high quality standards, is not afraid of direct exposure to ultraviolet radiation, and also does not hold back frost outside the structure very badly, and thermal energy inside it.The last two properties are very important for a garage, because in more common metal garages, the temperature inside them is not much different from the temperature outside, and therefore, in severe winter frosts, a car that is in a metal garage may simply not start, which will never happen to a car that is stored in a garage made of foam blocks.How to organize the foundation for the construction of a garage of their foam blocks?In general, the organization of the foundation for a garage made of foam blocks is no different from the organization of the foundation for capital construction from any other material. For our part, we would recommend making a foundation with a grillage, since this type of foundation is the cheapest and in all respects necessary for a foam block garage, it is not inferior to any other type of foundations. In addition, in this case you will be able to build a full-fledged garage cellar.To organize a foundation with a grillage, the first thing you need to drill wells in the amount of sixteen pieces. After all the wells under the foundation are ready, they need to be filled with concrete. For the foundation for the construction of a garage made of foam blocks, it is recommended to use M200 grade concrete, since it has the right level of strength and all the necessary set of properties that are necessary for the construction of a building, in this case a garage, made of foam blocks.After the wells are filled in, it is necessary to build a formwork, which must be reinforced with transverse boards. The thing is, if this is not done, during the pouring of the foundation, the formwork can "lead", which will lead to deformation of the shape of the foundation. It is worth noting that the wells must be reinforced with metal rods, which must be removed into the formwork to form a unity of construction. It turns out that in addition to the top layer of the foundation, there will be a reliable grip with the help of pillars with concrete from wells, and not just support on it.After the formwork is installed and fastened, you can start pouring it with concrete. The concrete solution should consist of one part cement, two parts sand and two parts crushed stone. It is best to mix it in a concrete mixer, but if there is no one, then you can mix everything manually, although it will take more effort and take more time. It is very important that the foundation is filled in at a time, if for some reason it cannot be done, before topping up the foundation, the existing concrete will need to be moistened.How to build garage walls from foam blocks?After the foundation for the garage is ready, you can start building walls of foam concrete blocks. It is worth noting that foam blocks are quite expensive material and if you want to save money, you can replace them with cheaper options: blocks of arbolite, cinder blocks and the like.Unlike a frame garage, there is nothing complicated in the construction of walls from such blocks. With each type of blocks, the package includes instructions for use.How to build an observation pit in the garage?First, you need to dig a hole. Next, with the help of roofing material, it is necessary to make its complete waterproofing. This is done in order to avoid deformation of the shape of the pit, due to the freezing of groundwater, which in one or another amount will approach it.After the waterproofing is done, you need to install the formwork and fill it with a solution similar to the one from which the foundation was made. You can remove the formwork in weeks, but the complete drying of the concrete mortar will take about three weeks.Organization of concrete floors in the garage from building blocks In order to make a concrete floor in the garage, it is enough to pour a concrete screed. This is a very simple process, but it requires knowledge about the sequence of actions.A brief instruction on it can be found below:1. To begin with, it is required to remove twenty to thirty centimeters of soil and put a waterproofing film on the bottom of the formed pit.2. Next, we pour ten centimeters of sand into the pit and ramm it.3. The next step is to close the sand layer with another layer of waterproofing film. It is worth noting that the film should be placed on the walls to avoid getting wet from the sides.4. Next, a crate of reinforcement is laid on the waterproofing layer, which should form squares, ten by fifteen centimeters. It is very important to fasten the reinforced bars together with wire so that they do not move. Also, at this stage we install the formwork.5. Now it remains only to pour the concrete screed. They usually pour a layer about eight millimeters thick.Just as in the case of the inspection pit, the formwork can be removed in a week, but it takes at least four weeks to wait for the concrete screed to dry, since it needs to be watered every day, otherwise there is a high probability of uneven drying and, as a result, the formation of internal and external cracks. Aqueles de vocês com um smartphone terão uma rica coleção de cassinos móveis. Atualmente, todos os cassinos online que hospedam hóspedes têm suporte móvel completo. Casino online com versões móveis incluídas https://www.slottica-brasil.com/ . A maioria desses sites é licenciada e regulamentada pela poderosa Curaçao Gaming Authority ou pela Gaming Commission. Pode ter certeza que seu dinheiro está em boas mãos.